BIGTREETECH Manta E3EZ, EZ2209, CB1, BLTouch
BIGTREETECH Manta E3EZ
BIGTREETECH Manta E3EZ
BIGTREETECH Manta E3EZ V1.0 Schematic
Interface
Pinout
Size
ADXL345 accelerometer
BIGTREETECH Manta E3EZ
BLTouch Wiring
BIGTREETECH Manta E3EZ
RGB Wiring
Klipper
Klipper
printer.cfg
[include mainsail.cfg]
[include macros/*.cfg]
[virtual_sdcard]
path: /home/biqu/printer_data/gcodes
on_error_gcode: CANCEL_PRINT
[mcu]
serial: /dev/serial/by-id/usb-Klipper_XXXXXXXXXXXXXXX
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
######################################################################
# Temperature Sensors
######################################################################
[temperature_sensor CB1]
sensor_type: temperature_host
min_temp: 10
max_temp: 100
[temperature_sensor E3EZ]
sensor_type: temperature_mcu
min_temp: 10
max_temp: 100
######################################################################
# Fan Settings
######################################################################
[heater_fan HotendFan]
pin: PB15
max_power: 1.0
fan_speed: 0.7
kick_start_time: 0.1
heater: extruder
heater_temp: 50.0
[fan]
pin: PA8
[temperature_fan BoardFan]
pin: PB14
max_power: 1.0
sensor_type: temperature_host
control:watermark
target_temp: 45
min_temp: 0
max_temp: 90
off_below: 0.10
kick_start_time: 0.50
max_speed: 0.9
min_speed: 0.3
######################################################################
# neopixel Settings
######################################################################
[neopixel Licht]
pin: PC7
chain_count: 2
initial_RED: 0.0
initial_GREEN: 1.0
initial_BLUE: 0.0
initial_WHITE: 0.0
######################################################################
# BLTouch Settings
######################################################################
[bltouch]
sensor_pin: PA6
control_pin: PA7
samples: 2
#horizontal_move_z: 10
speed: 20
x_offset: -31
y_offset: -8
#z_offset: 0.0
#####################################################################
# Bed Mesh Settings
######################################################################
[bed_mesh]
speed: 100
horizontal_move_z: 10
mesh_min: 10, 10
mesh_max: 133, 145
probe_count: 4, 4
mesh_pps: 2,2
fade_start: 1
fade_end: 10
fade_target: 0
######################################################################
# 128x64 Full Graphic Creality CR10 / ENDER 3 stockdisplay
######################################################################
[display]
lcd_type: st7920
cs_pin: EXP1_7
sclk_pin: EXP1_6
sid_pin: EXP1_8
encoder_pins: ^EXP1_5, ^EXP1_3
click_pin: ^!EXP1_2
[output_pin beeper]
pin: EXP1_1
########################################
# X configuration
########################################
[stepper_x]
step_pin: PA14
dir_pin: PA10
enable_pin: !PA13
microsteps: 16
rotation_distance: 40
endstop_pin: ^PC4
position_min: -20
position_endstop: -20
position_max: 165
homing_speed: 50
[tmc2209 stepper_x]
uart_pin: PB8
#diag_pin: PC4
run_current: 0.800
stealthchop_threshold: 999999
########################################
# Y configuration
########################################
[stepper_y]
step_pin: PC8
dir_pin: PA15
enable_pin: !PC14
microsteps: 16
rotation_distance: 40
endstop_pin: ^PB0
position_endstop: 0
position_min: -5
position_endstop: -5
position_max: 165
homing_speed: 50
[tmc2209 stepper_y]
uart_pin: PC9
#diag_pin: PB0
run_current: 0.800
stealthchop_threshold: 999999
########################################
# z configuration
########################################
[stepper_z]
step_pin: PD2
dir_pin: PD4
enable_pin: !PD3
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
#position_endstop: 0
position_max: 180
position_min: -2.0
[tmc2209 stepper_z]
uart_pin: PD0
#diag_pin: PC6
run_current: 0.650
stealthchop_threshold: 999999
[safe_z_home]
home_xy_position: 114, 87 # Change coordinates to the center of your print bed
speed: 50
z_hop: 10 # Move up 10mm
z_hop_speed: 5
########################################
# E configuration
########################################
[extruder]
step_pin: PD5
dir_pin: !PD6
enable_pin: !PB3
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PB11 #HE0
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA4 #TH0
#control: pid
#pid_Kp: 21.527
#pid_Ki: 1.063
#pid_Kd: 108.982
min_temp: 0
max_temp: 270
[tmc2209 extruder]
uart_pin: PD1
run_current: 0.800
stealthchop_threshold: 999999
[heater_bed]
heater_pin: PB2 #HB
sensor_type: EPCOS 100K B57560G104F #Generic 3950
sensor_pin: PA3 #TB
#control: watermark
min_temp: 0
max_temp: 130
[board_pins]
aliases:
# EXP1 header
EXP1_1=PC1, EXP1_3=PC3, EXP1_5=PC0, EXP1_7=PA2, EXP1_9=<GND>,
EXP1_2=PC2, EXP1_4=<RST>, EXP1_6=PA0, EXP1_8=PA1, EXP1_10=<5V>