Ender 2 pro printer.cfg
[include mainsail.cfg]
[include macros/*.cfg]
[virtual_sdcard]
path: /home/biqu/printer_data/gcodes
on_error_gcode: CANCEL_PRINT
[mcu]
serial: /dev/serial/by-id/usb-Klipper_stm32g0b1xx_43002C000B504B5735313920-if00
[temperature_sensor CB1]
sensor_type: temperature_host
min_temp: 10
max_temp: 100
[temperature_sensor CB1]
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
######################################################################
# Fan Control
######################################################################
[heater_fan hotend_fan]
pin: PA4
max_power: 1.0
fan_speed: 0.7
kick_start_time: 0.1
heater: extruder
heater_temp: 50.0
[fan]
pin: PA3
######################################################################
# BLTouch Settings
######################################################################
[bltouch]
sensor_pin: PC13
control_pin: PC15
samples: 2
#horizontal_move_z: 10
speed: 20
x_offset: -31
y_offset: -8
#z_offset: 0.0
######################################################################
# Bed Mesh Settings
######################################################################
[bed_mesh]
speed: 100
horizontal_move_z: 10
mesh_min: 10, 10
mesh_max: 133, 145
probe_count: 4, 4
mesh_pps: 2,2
fade_start: 1
fade_end: 10
fade_target: 0
######################################################################
# 128x64 Full Graphic Creality CR10 / ENDER 3 stockdisplay
######################################################################
# This section is used for a Creality "12864" display with a single
# ribbon cable between the display's EXP3 plug and the
# micro-controller board's EXP1 connector.
[display]
lcd_type: st7920
cs_pin: EXP1_7
sclk_pin: EXP1_6
sid_pin: EXP1_8
encoder_pins: ^EXP1_5, ^EXP1_3
click_pin: ^!EXP1_2
[output_pin beeper]
pin: EXP1_1
########################################
# TMC2209 configuration
########################################
[tmc2209 stepper_x]
uart_pin: PD9
run_current: 0.800
diag_pin: PD3
stealthchop_threshold: 999999
[tmc2209 stepper_y]
uart_pin: PD8
run_current: 0.800
diag_pin: PD2
stealthchop_threshold: 999999
[tmc2209 stepper_z]
uart_pin: PB10
run_current: 0.800
diag_pin: PC3
stealthchop_threshold: 999999
[tmc2209 extruder]
uart_pin: PB2
run_current: 0.600
diag_pin: PC2
stealthchop_threshold: 999999
########################################
# Stepper configuration
########################################
[stepper_x]
step_pin: PC8
dir_pin: PC9
enable_pin: !PA15
microsteps: 16
rotation_distance: 40
endstop_pin: ^PD3
position_min: -20
position_endstop: -20
position_max: 165
homing_speed: 50
[stepper_y]
step_pin: PA10
dir_pin: PA14
enable_pin: !PA13
microsteps: 16
rotation_distance: 40
endstop_pin: ^PD2
position_endstop: 0
position_min: -5
position_endstop: -5
position_max: 165
homing_speed: 50
[stepper_z]
step_pin: PC6
dir_pin: !PC7
enable_pin: !PA9
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
#position_endstop: 0
position_max: 180
position_min: -6.0
[safe_z_home]
home_xy_position: 114, 87 # Change coordinates to the center of your print bed
speed: 50
z_hop: 10 # Move up 10mm
z_hop_speed: 5
[extruder]
step_pin: PB12
dir_pin: PB11
enable_pin: !PA8
microsteps: 16
rotation_distance: 32.495
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PC5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA1
control: pid
pid_Kp: 21.527
pid_Ki: 1.063
pid_Kd: 108.982
min_temp: 0
max_temp: 250
max_extrude_only_distance: 100
[heater_bed]
heater_pin: PA5
sensor_type: Generic 3950
sensor_pin: PA0
control: watermark
min_temp: 0
max_temp: 80
[board_pins]
aliases:
# EXP1 header
EXP1_1=PD5, EXP1_3=PB3, EXP1_5=PB5, EXP1_7=PB7, EXP1_9=<GND>,
EXP1_2=PD4, EXP1_4=PD6, EXP1_6=PB4, EXP1_8=PB6, EXP1_10=<5V>,
# EXP2 header
EXP2_1=PB14, EXP2_3=PB8, EXP2_5=PC10, EXP2_7=PC12, EXP2_9=<GND>,
EXP2_2=PB13, EXP2_4=PB9, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<NC>
